极速赛车168 XM4（Low ESR，high ripple current，high viltage，high temperature） Archives - Xuansn Capacitor

极速赛车168 Solid Capacitor 820uf 4v SMD low ESR manufacture XUANSN

FilmCapacitor — Thu, 17 Nov 2022 10:08:55 +0000

The full name of solid capacitor 820uf 4v is: solid aluminum electrolytic capacitors. The biggest difference between it and ordinary capacitors (ie, liquid aluminum electrolytic capacitors) is the use of different dielectric materials. The dielectric material of liquid aluminum capacitors is electrolyte, while the dielectric material of solid capacitors is conductive polymer materials.

XM4 Series-Solid Capacitor 820uf 4v

● Low ESR, High ripple, miniaturized,high temperature
● SMD type: lead free reflow soldering condition at 260℃ peak correspondence
● RoHS Compliant

Item	Characteristics
Temperature Range	-55~+105℃
Specification33	820UF4V
Capacitance Tolerance	±20% (M) (at 20°C, 120Hz)
Dissipation Factor (tanδ)	tanδ (max.)=0.08(2.5~6.3V) tanδ (max.)=0.12(10~100V) (at 20°C, 120Hz)
Leakage Current	I≤0.2 CV or 500μA（2.5~25V,take the maximum）I≤0.1 CV or 500μA（35~100V,take the maximum） Where, I: Max.leakage current (μA), C: Nominal capacitance (μF),V:Rated voltage (V),(at 20 °C after 2 minutes)
Low Temperature Characteristics (Max. Impedance Ratio)	Z(-25°C)/Z(+20°C)≦1.25 Z(-40°C)/Z(+20°C)≦1.25 (at 100kHz)
Endurance	The following specifications shall be satisfied when the capacitors are restored to 20°C after DC voltage plus the rated ripple current is applied for 2,000 hours at 105°C. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Damp heat（steady state）	The specifications listed below shall be satisfied when the capacitors are restored to 20℃ after application of rated voltage for 1000 hours at 60℃,90%~95%RH. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Surge Voltage	Surge voltage = rated voltage * 1.15 (V) The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltages specified at 105℃ for 30 seconds through a protective resistor（Rc=1kΩ）and discharge for 5 minutes 30 seconds Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Resistance to soldering heat	Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Capacitance Change :≤±10% of the initial value D.F. (tanδ):≤130% of the initial specified value ESR:≤130% of the initial specified value Leakage Current :≤The initial specified value

Dimensions

Rated Ripple Current Correction Coefficient

Frequency (Hz)	120Hz≦f＜1kHz	1kHz≦f＜10kHz	10kHz≦f＜100kHz	100kHz≦f＜500kHz
Coefficient	0.05	0.30	0.70	1.00

Parameters Table

Rated voltage（V）	Rated Capacitance（μf）	Case size D*L(mm)	ESR(mΩ） at 20℃ 100kHz	Leakage Current (μA)	Rated ripple current（mArms/105℃/100kHz）
4	820	6.3*9	30	656	2369

Rated voltage（V）

Rated Capacitance（μf）

Case size D*L(mm)

ESR(mΩ）

at 20℃ 100kHz

Leakage Current

(μA)

Rated ripple current（mArms/105℃/100kHz）

820

6.3*9

656

2369

How to order

XM4 821 M 0G D06L09 T

XM4:Series code

821:Capacitance code

M:Capacitance tolerance code

0G:Voltage code

D06L09:Size code

T:Packing number

Our advantage

1. Have 18 years experiences in capacitor industry. Be able to quickly understand the needs of customers and give feedback quickly.

2. Covers all capacitors: Electrolytic capacitors, film capacitors, safety capacitors, ceramic capacitors, super capacitors.

3.With 200 production lines, the sample delivery time is 3 days, and the bulk goods delivery time is 2 weeks.

4.The company has its own R&D team and after-sales team, providing complete pre-sale, in-sale and after-sale services.

Contact us

We are a supplier of electrolytic capacitor, and we have rich experiences in this field. Our daily production capacity can reach 7 million electrolytic capacitors, the sample period is 3 days, and the production cycle is 10 days. We will give you great support in terms of price, quality and delivery time.

And Support Customer’s Visit To The Factory

e-mail： sales1@xuanxcapacitors.com

Pho（whatsapp）：+ 86-18825879082

Skype：Coco.psh

website：xuanxcapacitors.com

The post Solid Capacitor 820uf 4v SMD low ESR manufacture XUANSN appeared first on Xuansn Capacitor.

极速赛车168 Solid Capacitor 680uf 2.5v SMD low ESR manufacture XUANSN

FilmCapacitor — Thu, 17 Nov 2022 09:58:51 +0000

The full name of solid capacitor 680uf 2.5v is: solid aluminum electrolytic capacitors. The biggest difference between it and ordinary capacitors (ie, liquid aluminum electrolytic capacitors) is the use of different dielectric materials. The dielectric material of liquid aluminum capacitors is electrolyte, while the dielectric material of solid capacitors is conductive polymer materials.

XM4 Series-Solid Capacitor 680uf 2.5v

● Low ESR, High ripple, miniaturized,high temperature
● SMD type: lead free reflow soldering condition at 260℃ peak correspondence
● RoHS Compliant

Item	Characteristics
Temperature Range	-55~+105℃
Specification33	680UF2.5V
Capacitance Tolerance	±20% (M) (at 20°C, 120Hz)
Dissipation Factor (tanδ)	tanδ (max.)=0.08(2.5~6.3V) tanδ (max.)=0.12(10~100V) (at 20°C, 120Hz)
Leakage Current	I≤0.2 CV or 500μA（2.5~25V,take the maximum）I≤0.1 CV or 500μA（35~100V,take the maximum） Where, I: Max.leakage current (μA), C: Nominal capacitance (μF),V:Rated voltage (V),(at 20 °C after 2 minutes)
Low Temperature Characteristics (Max. Impedance Ratio)	Z(-25°C)/Z(+20°C)≦1.25 Z(-40°C)/Z(+20°C)≦1.25 (at 100kHz)
Endurance	The following specifications shall be satisfied when the capacitors are restored to 20°C after DC voltage plus the rated ripple current is applied for 2,000 hours at 105°C. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Damp heat（steady state）	The specifications listed below shall be satisfied when the capacitors are restored to 20℃ after application of rated voltage for 1000 hours at 60℃,90%~95%RH. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Surge Voltage	Surge voltage = rated voltage * 1.15 (V) The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltages specified at 105℃ for 30 seconds through a protective resistor（Rc=1kΩ）and discharge for 5 minutes 30 seconds Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Resistance to soldering heat	Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Capacitance Change :≤±10% of the initial value D.F. (tanδ):≤130% of the initial specified value ESR:≤130% of the initial specified value Leakage Current :≤The initial specified value

Dimensions

Rated Ripple Current Correction Coefficient

Frequency (Hz)	120Hz≦f＜1kHz	1kHz≦f＜10kHz	10kHz≦f＜100kHz	100kHz≦f＜500kHz
Coefficient	0.05	0.30	0.70	1.00

Parameters Table

Rated voltage（V）	Rated Capacitance（μf）	Case size D*L(mm)	ESR(mΩ） at 20℃ 100kHz	Leakage Current (μA)	Rated ripple current（mArms/105℃/100kHz）
2.5	680	6.3*9	30	500	2369

Rated voltage（V）

Rated Capacitance（μf）

Case size D*L(mm)

ESR(mΩ）

at 20℃ 100kHz

Leakage Current

(μA)

Rated ripple current（mArms/105℃/100kHz）

2.5

680

6.3*9

500

2369

How to order

XM4 681 M 0E D06L09 T

XM4:Series code

681:Capacitance code

M:Capacitance tolerance code

0E:Voltage code

D06L09:Size code

T:Packing number

Our advantage

1. Have 18 years experiences in capacitor industry. Be able to quickly understand the needs of customers and give feedback quickly.

2. Covers all capacitors: Electrolytic capacitors, film capacitors, safety capacitors, ceramic capacitors, super capacitors.

3.With 200 production lines, the sample delivery time is 3 days, and the bulk goods delivery time is 2 weeks.

4.The company has its own R&D team and after-sales team, providing complete pre-sale, in-sale and after-sale services.

Contact us

And Support Customer’s Visit To The Factory

e-mail： sales1@xuanxcapacitors.com

Pho（whatsapp）：+ 86-18825879082

Skype：Coco.psh

website：xuanxcapacitors.com

The post Solid Capacitor 680uf 2.5v SMD low ESR manufacture XUANSN appeared first on Xuansn Capacitor.

极速赛车168 Solid Capacitor 470uf 2.5v SMD low ESR manufacture XUANSN

FilmCapacitor — Thu, 17 Nov 2022 09:52:45 +0000

The full name of solid capacitor 470uf 2.5v is: solid aluminum electrolytic capacitors. The biggest difference between it and ordinary capacitors (ie, liquid aluminum electrolytic capacitors) is the use of different dielectric materials. The dielectric material of liquid aluminum capacitors is electrolyte, while the dielectric material of solid capacitors is conductive polymer materials.

XM4 Series-Solid Capacitor 470uf 2.5v

● Low ESR, High ripple, miniaturized,high temperature
● SMD type: lead free reflow soldering condition at 260℃ peak correspondence
● RoHS Compliant

Item	Characteristics
Temperature Range	-55~+105℃
Specification33	470UF2.5V
Capacitance Tolerance	±20% (M) (at 20°C, 120Hz)
Dissipation Factor (tanδ)	tanδ (max.)=0.08(2.5~6.3V) tanδ (max.)=0.12(10~100V) (at 20°C, 120Hz)
Leakage Current	I≤0.2 CV or 500μA（2.5~25V,take the maximum）I≤0.1 CV or 500μA（35~100V,take the maximum） Where, I: Max.leakage current (μA), C: Nominal capacitance (μF),V:Rated voltage (V),(at 20 °C after 2 minutes)
Low Temperature Characteristics (Max. Impedance Ratio)	Z(-25°C)/Z(+20°C)≦1.25 Z(-40°C)/Z(+20°C)≦1.25 (at 100kHz)
Endurance	The following specifications shall be satisfied when the capacitors are restored to 20°C after DC voltage plus the rated ripple current is applied for 2,000 hours at 105°C. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Damp heat（steady state）	The specifications listed below shall be satisfied when the capacitors are restored to 20℃ after application of rated voltage for 1000 hours at 60℃,90%~95%RH. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Surge Voltage	Surge voltage = rated voltage * 1.15 (V) The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltages specified at 105℃ for 30 seconds through a protective resistor（Rc=1kΩ）and discharge for 5 minutes 30 seconds Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Resistance to soldering heat	Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Capacitance Change :≤±10% of the initial value D.F. (tanδ):≤130% of the initial specified value ESR:≤130% of the initial specified value Leakage Current :≤The initial specified value

Dimensions

Rated Ripple Current Correction Coefficient

Frequency (Hz)	120Hz≦f＜1kHz	1kHz≦f＜10kHz	10kHz≦f＜100kHz	100kHz≦f＜500kHz
Coefficient	0.05	0.30	0.70	1.00

Parameters Table

Rated voltage（V）	Rated Capacitance（μf）	Case size D*L(mm)	ESR(mΩ） at 20℃ 100kHz	Leakage Current (μA)	Rated ripple current（mArms/105℃/100kHz）
2.5	470	6.3*9	30	500	2369

Rated voltage（V）

Rated Capacitance（μf）

Case size D*L(mm)

ESR(mΩ）

at 20℃ 100kHz

Leakage Current

(μA)

Rated ripple current（mArms/105℃/100kHz）

2.5

470

6.3*9

500

2369

How to order

XM4 471 M 0E D06L09 T

XM4:Series code

471:Capacitance code

M:Capacitance tolerance code

0E:Voltage code

D06L09:Size code

T:Packing number

Our advantage

1. Have 18 years experiences in capacitor industry. Be able to quickly understand the needs of customers and give feedback quickly.

2. Covers all capacitors: Electrolytic capacitors, film capacitors, safety capacitors, ceramic capacitors, super capacitors.

3.With 200 production lines, the sample delivery time is 3 days, and the bulk goods delivery time is 2 weeks.

4.The company has its own R&D team and after-sales team, providing complete pre-sale, in-sale and after-sale services.

Contact us

And Support Customer’s Visit To The Factory

e-mail： sales1@xuanxcapacitors.com

Pho（whatsapp）：+ 86-18825879082

Skype：Coco.psh

website：xuanxcapacitors.com

The post Solid Capacitor 470uf 2.5v SMD low ESR manufacture XUANSN appeared first on Xuansn Capacitor.

极速赛车168 Capacitor 68uf 80v SMD low ESR type manufacturing vendor

FilmCapacitor — Thu, 17 Nov 2022 09:45:34 +0000

The full name of solid capacitor 68uf 80v is: solid aluminum electrolytic capacitors. The biggest difference between it and ordinary capacitors (ie, liquid aluminum electrolytic capacitors) is the use of different dielectric materials. The dielectric material of liquid aluminum capacitors is electrolyte, while the dielectric material of solid capacitors is conductive polymer materials.

XM4 Series-Capacitor 68uf 80v

● Low ESR, High ripple, miniaturized,high temperature
● SMD type: lead free reflow soldering condition at 260℃ peak correspondence
● RoHS Compliant

Item	Characteristics
Temperature Range	-55~+105℃
Specification33	68UF80V
Capacitance Tolerance	±20% (M) (at 20°C, 120Hz)
Dissipation Factor (tanδ)	tanδ (max.)=0.08(2.5~6.3V) tanδ (max.)=0.12(10~100V) (at 20°C, 120Hz)
Leakage Current	I≤0.2 CV or 500μA（2.5~25V,take the maximum）I≤0.1 CV or 500μA（35~100V,take the maximum） Where, I: Max.leakage current (μA), C: Nominal capacitance (μF),V:Rated voltage (V),(at 20 °C after 2 minutes)
Low Temperature Characteristics (Max. Impedance Ratio)	Z(-25°C)/Z(+20°C)≦1.25 Z(-40°C)/Z(+20°C)≦1.25 (at 100kHz)
Endurance	The following specifications shall be satisfied when the capacitors are restored to 20°C after DC voltage plus the rated ripple current is applied for 2,000 hours at 105°C. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Damp heat（steady state）	The specifications listed below shall be satisfied when the capacitors are restored to 20℃ after application of rated voltage for 1000 hours at 60℃,90%~95%RH. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Surge Voltage	Surge voltage = rated voltage * 1.15 (V) The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltages specified at 105℃ for 30 seconds through a protective resistor（Rc=1kΩ）and discharge for 5 minutes 30 seconds Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Resistance to soldering heat	Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Capacitance Change :≤±10% of the initial value D.F. (tanδ):≤130% of the initial specified value ESR:≤130% of the initial specified value Leakage Current :≤The initial specified value

Dimensions

Rated Ripple Current Correction Coefficient

Frequency (Hz)	120Hz≦f＜1kHz	1kHz≦f＜10kHz	10kHz≦f＜100kHz	100kHz≦f＜500kHz
Coefficient	0.05	0.30	0.70	1.00

Parameters Table

Rated voltage（V）	Rated Capacitance（μf）	Case size D*L(mm)	ESR(mΩ） at 20℃ 100kHz	Leakage Current (μA)	Rated ripple current（mArms/105℃/100kHz）
80	68	10*12.6	120	299	450

Rated voltage（V）

Rated Capacitance（μf）

Case size D*L(mm)

ESR(mΩ）

at 20℃ 100kHz

Leakage Current

(μA)

Rated ripple current（mArms/105℃/100kHz）

10*12.6

120

299

450

How to order

XM4 680 M 1K D10L13 T

XM4:Series code

680:Capacitance code

M:Capacitance tolerance code

1K:Voltage code

D10L13:Size code

T:Packing number

Our advantage

1. Have 18 years experiences in capacitor industry. Be able to quickly understand the needs of customers and give feedback quickly.

2. Covers all capacitors: Electrolytic capacitors, film capacitors, safety capacitors, ceramic capacitors, super capacitors.

3.With 200 production lines, the sample delivery time is 3 days, and the bulk goods delivery time is 2 weeks.

4.The company has its own R&D team and after-sales team, providing complete pre-sale, in-sale and after-sale services.

Contact us

And Support Customer’s Visit To The Factory

e-mail： sales1@xuanxcapacitors.com

Pho（whatsapp）：+ 86-18825879082

Skype：Coco.psh

website：xuanxcapacitors.com

The post Capacitor 68uf 80v SMD low ESR type manufacturing vendor appeared first on Xuansn Capacitor.

极速赛车168 Capacitor 560UF 4V SMD low ESR manufacture XUANSN

FilmCapacitor — Thu, 17 Nov 2022 09:43:50 +0000

The full name of solid capacitor 560uf 4v is: solid aluminum electrolytic capacitors. The biggest difference between it and ordinary capacitors (ie, liquid aluminum electrolytic capacitors) is the use of different dielectric materials. The dielectric material of liquid aluminum capacitors is electrolyte, while the dielectric material of solid capacitors is conductive polymer materials.

XM4 Series-Solid Capacitor 560uf 4v

● Low ESR, High ripple, miniaturized,high temperature
● SMD type: lead free reflow soldering condition at 260℃ peak correspondence
● RoHS Compliant

Item	Characteristics
Temperature Range	-55~+105℃
Specification33	560UF4V
Capacitance Tolerance	±20% (M) (at 20°C, 120Hz)
Dissipation Factor (tanδ)	tanδ (max.)=0.08(2.5~6.3V) tanδ (max.)=0.12(10~100V) (at 20°C, 120Hz)
Leakage Current	I≤0.2 CV or 500μA（2.5~25V,take the maximum）I≤0.1 CV or 500μA（35~100V,take the maximum） Where, I: Max.leakage current (μA), C: Nominal capacitance (μF),V:Rated voltage (V),(at 20 °C after 2 minutes)
Low Temperature Characteristics (Max. Impedance Ratio)	Z(-25°C)/Z(+20°C)≦1.25 Z(-40°C)/Z(+20°C)≦1.25 (at 100kHz)
Endurance	The following specifications shall be satisfied when the capacitors are restored to 20°C after DC voltage plus the rated ripple current is applied for 2,000 hours at 105°C. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Damp heat（steady state）	The specifications listed below shall be satisfied when the capacitors are restored to 20℃ after application of rated voltage for 1000 hours at 60℃,90%~95%RH. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Surge Voltage	Surge voltage = rated voltage * 1.15 (V) The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltages specified at 105℃ for 30 seconds through a protective resistor（Rc=1kΩ）and discharge for 5 minutes 30 seconds Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Resistance to soldering heat	Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Capacitance Change :≤±10% of the initial value D.F. (tanδ):≤130% of the initial specified value ESR:≤130% of the initial specified value Leakage Current :≤The initial specified value

Dimensions

Rated Ripple Current Correction Coefficient

Frequency (Hz)	120Hz≦f＜1kHz	1kHz≦f＜10kHz	10kHz≦f＜100kHz	100kHz≦f＜500kHz
Coefficient	0.05	0.30	0.70	1.00

Parameters Table

Rated voltage（V）	Rated Capacitance（μf）	Case size D*L(mm)	ESR(mΩ） at 20℃ 100kHz	Leakage Current (μA)	Rated ripple current（mArms/105℃/100kHz）
4	560	6.3*9	30	500	2369

Rated voltage（V）

Rated Capacitance（μf）

Case size D*L(mm)

ESR(mΩ）

at 20℃ 100kHz

Leakage Current

(μA)

Rated ripple current（mArms/105℃/100kHz）

560

6.3*9

500

2369

How to order-Capacitor 560uf 4v

XM4 561 M 0G D06L09 T

XM4:Series code

561:Capacitance code

M:Capacitance tolerance code

0G:Voltage code

D06L09:Size code

T:Packing number

Our advantage

1. Have 18 years experiences in capacitor industry. Be able to quickly understand the needs of customers and give feedback quickly.

2. Covers all capacitors: Electrolytic capacitors, film capacitors, safety capacitors, ceramic capacitors, super capacitors.

3.With 200 production lines, the sample delivery time is 3 days, and the bulk goods delivery time is 2 weeks.

4.The company has its own R&D team and after-sales team, providing complete pre-sale, in-sale and after-sale services.

Contact us

And Support Customer’s Visit To The Factory

e-mail： sales1@xuanxcapacitors.com

Pho（whatsapp）：+ 86-18825879082

Skype：Coco.psh

website：xuanxcapacitors.com

The post Capacitor 560UF 4V SMD low ESR manufacture XUANSN appeared first on Xuansn Capacitor.

极速赛车168 Capacitor 33uf 100v SMD low ESR type manufacture

FilmCapacitor — Thu, 17 Nov 2022 09:42:29 +0000

The full name of solid capacitor 33uf 100v is: solid aluminum electrolytic capacitors. The biggest difference between it and ordinary capacitors (ie, liquid aluminum electrolytic capacitors) is the use of different dielectric materials. The dielectric material of liquid aluminum capacitors is electrolyte, while the dielectric material of solid capacitors is conductive polymer materials.

XM4 Series-Capacitor 33uf 100v

● Low ESR, High ripple, miniaturized,high temperature
● SMD type: lead free reflow soldering condition at 260℃ peak correspondence
● RoHS Compliant

Item	Characteristics
Temperature Range	-55~+105℃
Specification33	33UF100V
Capacitance Tolerance	±20% (M) (at 20°C, 120Hz)
Dissipation Factor (tanδ)	tanδ (max.)=0.08(2.5~6.3V) tanδ (max.)=0.12(10~100V) (at 20°C, 120Hz)
Leakage Current	I≤0.2 CV or 500μA（2.5~25V,take the maximum）I≤0.1 CV or 500μA（35~100V,take the maximum） Where, I: Max.leakage current (μA), C: Nominal capacitance (μF),V:Rated voltage (V),(at 20 °C after 2 minutes)
Low Temperature Characteristics (Max. Impedance Ratio)	Z(-25°C)/Z(+20°C)≦1.25 Z(-40°C)/Z(+20°C)≦1.25 (at 100kHz)
Endurance	The following specifications shall be satisfied when the capacitors are restored to 20°C after DC voltage plus the rated ripple current is applied for 2,000 hours at 105°C. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Damp heat（steady state）	The specifications listed below shall be satisfied when the capacitors are restored to 20℃ after application of rated voltage for 1000 hours at 60℃,90%~95%RH. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Surge Voltage	Surge voltage = rated voltage * 1.15 (V) The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltages specified at 105℃ for 30 seconds through a protective resistor（Rc=1kΩ）and discharge for 5 minutes 30 seconds Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Resistance to soldering heat	Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Capacitance Change :≤±10% of the initial value D.F. (tanδ):≤130% of the initial specified value ESR:≤130% of the initial specified value Leakage Current :≤The initial specified value

Dimensions

Rated Ripple Current Correction Coefficient

Frequency (Hz)	120Hz≦f＜1kHz	1kHz≦f＜10kHz	10kHz≦f＜100kHz	100kHz≦f＜500kHz
Coefficient	0.05	0.30	0.70	1.00

Parameters Table

Rated voltage（V）	Rated Capacitance（μf）	Case size D*L(mm)	ESR(mΩ） at 20℃ 100kHz	Leakage Current (μA)	Rated ripple current（mArms/105℃/100kHz）
100	33	10*12.6	70	330	950

Rated voltage（V）

Rated Capacitance（μf）

Case size D*L(mm)

ESR(mΩ）

at 20℃ 100kHz

Leakage Current

(μA)

Rated ripple current（mArms/105℃/100kHz）

100

10*12.6

330

950

How to order

XM4 330 M 2A D10L13 T

XM4:Series code

330:Capacitance code

M:Capacitance tolerance code

2A:Voltage code

D10L13:Size code

T:Packing number

Our advantage

1. Have 18 years experiences in capacitor industry. Be able to quickly understand the needs of customers and give feedback quickly.

2. Covers all capacitors: Electrolytic capacitors, film capacitors, safety capacitors, ceramic capacitors, super capacitors.

3.With 200 production lines, the sample delivery time is 3 days, and the bulk goods delivery time is 2 weeks.

4.The company has its own R&D team and after-sales team, providing complete pre-sale, in-sale and after-sale services.

Contact us

And Support Customer’s Visit To The Factory

e-mail： sales1@xuanxcapacitors.com

Pho（whatsapp）：+ 86-18825879082

Skype：Coco.psh

website：xuanxcapacitors.com

The post Capacitor 33uf 100v SMD low ESR type manufacture appeared first on Xuansn Capacitor.

极速赛车168 Capacitor 22uf 100v SMD low ESR type manufacturing vendor

FilmCapacitor — Thu, 17 Nov 2022 09:39:24 +0000

The full name of solid capacitor 22uf 100v is: solid aluminum electrolytic capacitors. The biggest difference between it and ordinary capacitors (ie, liquid aluminum electrolytic capacitors) is the use of different dielectric materials. The dielectric material of liquid aluminum capacitors is electrolyte, while the dielectric material of solid capacitors is conductive polymer materials.

XM4 Series-Capacitor 22uf 100v

● Low ESR, High ripple, miniaturized,high temperature
● SMD type: lead free reflow soldering condition at 260℃ peak correspondence
● RoHS Compliant

Item	Characteristics
Temperature Range	-55~+105℃
Specification33	22UF100V
Capacitance Tolerance	±20% (M) (at 20°C, 120Hz)
Dissipation Factor (tanδ)	tanδ (max.)=0.08(2.5~6.3V) tanδ (max.)=0.12(10~100V) (at 20°C, 120Hz)
Leakage Current	I≤0.2 CV or 500μA（2.5~25V,take the maximum）I≤0.1 CV or 500μA（35~100V,take the maximum） Where, I: Max.leakage current (μA), C: Nominal capacitance (μF),V:Rated voltage (V),(at 20 °C after 2 minutes)
Low Temperature Characteristics (Max. Impedance Ratio)	Z(-25°C)/Z(+20°C)≦1.25 Z(-40°C)/Z(+20°C)≦1.25 (at 100kHz)
Endurance	The following specifications shall be satisfied when the capacitors are restored to 20°C after DC voltage plus the rated ripple current is applied for 2,000 hours at 105°C. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Damp heat（steady state）	The specifications listed below shall be satisfied when the capacitors are restored to 20℃ after application of rated voltage for 1000 hours at 60℃,90%~95%RH. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Surge Voltage	Surge voltage = rated voltage * 1.15 (V) The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltages specified at 105℃ for 30 seconds through a protective resistor（Rc=1kΩ）and discharge for 5 minutes 30 seconds Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Resistance to soldering heat	Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Capacitance Change :≤±10% of the initial value D.F. (tanδ):≤130% of the initial specified value ESR:≤130% of the initial specified value Leakage Current :≤The initial specified value

Dimensions

Rated Ripple Current Correction Coefficient

Frequency (Hz)	120Hz≦f＜1kHz	1kHz≦f＜10kHz	10kHz≦f＜100kHz	100kHz≦f＜500kHz
Coefficient	0.05	0.30	0.70	1.00

Parameters Table

Rated voltage（V）	Rated Capacitance（μf）	Case size D*L(mm)	ESR(mΩ） at 20℃ 100kHz	Leakage Current (μA)	Rated ripple current（mArms/105℃/100kHz）
100	22	8*12.6	70	299	750

Rated voltage（V）

Rated Capacitance（μf）

Case size D*L(mm)

ESR(mΩ）

at 20℃ 100kHz

Leakage Current

(μA)

Rated ripple current（mArms/105℃/100kHz）

100

8*12.6

299

750

How to order

XM4 220 M 2A D08L13 T

XM4:Series code

220:Capacitance code

M:Capacitance tolerance code

2A:Voltage code

D08L13:Size code

T:Packing number

Our advantage

1. Have 18 years experiences in capacitor industry. Be able to quickly understand the needs of customers and give feedback quickly.

2. Covers all capacitors: Electrolytic capacitors, film capacitors, safety capacitors, ceramic capacitors, super capacitors.

3.With 200 production lines, the sample delivery time is 3 days, and the bulk goods delivery time is 2 weeks.

4.The company has its own R&D team and after-sales team, providing complete pre-sale, in-sale and after-sale services.

Contact us

And Support Customer’s Visit To The Factory

e-mail： sales1@xuanxcapacitors.com

Pho（whatsapp）：+ 86-18825879082

Skype：Coco.psh

website：xuanxcapacitors.com

The post Capacitor 22uf 100v SMD low ESR type manufacturing vendor appeared first on Xuansn Capacitor.

极速赛车168 Capacitor 22uf 80v SMD low ESR type manufacturing vendor

FilmCapacitor — Thu, 17 Nov 2022 09:36:37 +0000

The full name of solid capacitor 22uf 80v is: solid aluminum electrolytic capacitors. The biggest difference between it and ordinary capacitors (ie, liquid aluminum electrolytic capacitors) is the use of different dielectric materials. The dielectric material of liquid aluminum capacitors is electrolyte, while the dielectric material of solid capacitors is conductive polymer materials.

XM4 Series-Capacitor 22uf 80v

● Low ESR, High ripple, miniaturized,high temperature
● SMD type: lead free reflow soldering condition at 260℃ peak correspondence
● RoHS Compliant

Item	Characteristics
Temperature Range	-55~+105℃
Specification33	22UF80V
Capacitance Tolerance	±20% (M) (at 20°C, 120Hz)
Dissipation Factor (tanδ)	tanδ (max.)=0.08(2.5~6.3V) tanδ (max.)=0.12(10~100V) (at 20°C, 120Hz)
Leakage Current	I≤0.2 CV or 500μA（2.5~25V,take the maximum）I≤0.1 CV or 500μA（35~100V,take the maximum） Where, I: Max.leakage current (μA), C: Nominal capacitance (μF),V:Rated voltage (V),(at 20 °C after 2 minutes)
Low Temperature Characteristics (Max. Impedance Ratio)	Z(-25°C)/Z(+20°C)≦1.25 Z(-40°C)/Z(+20°C)≦1.25 (at 100kHz)
Endurance	The following specifications shall be satisfied when the capacitors are restored to 20°C after DC voltage plus the rated ripple current is applied for 2,000 hours at 105°C. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Damp heat（steady state）	The specifications listed below shall be satisfied when the capacitors are restored to 20℃ after application of rated voltage for 1000 hours at 60℃,90%~95%RH. Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Surge Voltage	Surge voltage = rated voltage * 1.15 (V) The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltages specified at 105℃ for 30 seconds through a protective resistor（Rc=1kΩ）and discharge for 5 minutes 30 seconds Capacitance Change :≤±20% of the initial value D.F. (tanδ):≤150% of the initial specified value ESR:≤150% of the initial specified value Leakage Current :≤The initial specified value
Resistance to soldering heat	Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Capacitance Change :≤±10% of the initial value D.F. (tanδ):≤130% of the initial specified value ESR:≤130% of the initial specified value Leakage Current :≤The initial specified value

Dimensions

Rated Ripple Current Correction Coefficient

Frequency (Hz)	120Hz≦f＜1kHz	1kHz≦f＜10kHz	10kHz≦f＜100kHz	100kHz≦f＜500kHz
Coefficient	0.05	0.30	0.70	1.00

Parameters Table

Rated voltage（V）	Rated Capacitance（μf）	Case size D*L(mm)	ESR(mΩ） at 20℃ 100kHz	Leakage Current (μA)	Rated ripple current（mArms/105℃/100kHz）
80	10	6.3*9	120	299	450

Rated voltage（V）

Rated Capacitance（μf）

Case size D*L(mm)

ESR(mΩ）

at 20℃ 100kHz

Leakage Current

(μA)

Rated ripple current（mArms/105℃/100kHz）

6.3*9

120

299

450

How to order

XM4 100 M 1K D06L09 T

XM4:Series code

100:Capacitance code

M:Capacitance tolerance code

1K:Voltage code

D06L09:Size code

T:Packing number

Our advantage

1. Have 18 years experiences in capacitor industry. Be able to quickly understand the needs of customers and give feedback quickly.

2. Covers all capacitors: Electrolytic capacitors, film capacitors, safety capacitors, ceramic capacitors, super capacitors.

3.With 200 production lines, the sample delivery time is 3 days, and the bulk goods delivery time is 2 weeks.

4.The company has its own R&D team and after-sales team, providing complete pre-sale, in-sale and after-sale services.

Contact us

And Support Customer’s Visit To The Factory

e-mail： sales1@xuanxcapacitors.com

Pho（whatsapp）：+ 86-18825879082

Skype：Coco.psh

website：xuanxcapacitors.com

The post Capacitor 22uf 80v SMD low ESR type manufacturing vendor appeared first on Xuansn Capacitor.